0 products currently in stock. Call our team for lead times if needed.


Industrial PROFIBUS-to-fiber converters



Industrial PROFIBUS to Fiber Optic Converter, ST Single-mode, -40 to 75 ℃

Series Description


The ICF-1180I industrial PROFIBUS-to-fiber converters are used to convert PROFIBUS signals from copper to optical fiber. The converters are used to extend serial transmission up to 4 km (multi-mode fiber) or up to 45 km (single-mode fiber).
The ICF-1180I provides 2 kV isolation protection for the PROFIBUS system and dual power inputs to ensure that your PROFIBUS device will perform uninterrupted.

Fiber Cable Test Function

Fiber-optic cables are usually deployed for long-distance communication. To ensure proper communication across the fiber-optic cables, engineers use fiber sensors. A fiber cable test function through DIP switch adjustments helps ICF-11801 converters eliminate the need to rely on fiber-optic sensors.

This function not only detects fiber communication abnormalities but also validates the format of the received packet. It can also determine which side (Tx or Rx) is causing the problem.


When the PROFIBUS device malfunctions or the serial interface fails, it will generate electrical noise, resulting in bus failure. Traditional media converters will let the noise signal pass through the fiber and on to the other converter. This will disrupt data transmissions between the two buses and eventually communication ceases across the entire system. When this occurs, the engineer will not be able to easily locate the failed device because the entire PROFIBUS network is down. To avoid this situation, the ICF-1180I was designed to detect and recognize noise signals. If the bus fails on one side, the noise signal will not propagate through the ICF-1180I and affect additional bus segments. In addition, the ICF-1180I will also trigger an alarm notification to the field engineer on the location of the failure.

Auto/Manual Baudrate Settings

The ICF-1180I Series simply converts the signal back and forth between PROFIBUS and fiber. The ICF-1180I Series works under baudrates between 9.6 kbps to 12 Mbps. Engineers do not need to know the baudrate of the connected PROFIBUS device.

The ICF-1180I Series can automatically detect the baudrate of the PROFIBUS device and apply this baudrate directly. This is an extremely convenient feature. If necessary, baudrates can be set to a fixed value via DIP switches.

Fiber Inverse Function

The ICF-1180I provides a fiber inverse function to choose fiber-optic light ON or light OFF when sending logic signal ‘1’. For default settings, fiber-optic is light OFF when sending logic signal ‘1’; in Fiber Inverse mode, fiber-optic is light ON when sending logic signal ‘1’.

This feature provides greater compatibility when the ICF-1180I converter is integrated with PROFIBUS converters of other manufacturers. Please refer to third-party user manuals when using this feature.

Fiber Link Monitor

The ICF-1180I converters provide a fiber link monitor function to detect the communication errors on either the fiber side or PROFIBUS side. Once there is an error in communication, the corresponding LED will turn red, and the relay alarm will be activated.

Fiber Signal Intensity Diagnosis

In some circumstances, you may need to measure the reception level of the fiber-optic port with a voltmeter, which can be connected while the device is operating (doing so will not affect data transmission). The measurement can be taken with a voltmeter and read on a PLC that uses floating high impedance analog inputs, which allow you to do the following:

  • Record the incoming optical power for later measurement (e.g., to indicate aging or damage).

  • Carry out a good/bad test (limit value).

Additional information

Industrial Protocols

No. of Ports


Input Current

Input Voltage




Warranty Period


IP Rating

Operating Temperature

-40 to 75°C (-40 to 167°F)

Ambient Relative Humidity



Need Support?

We understand that it can be difficult to find the right products for your needs. That’s why our dedicated customer support team is available to assist you in any way possible. Whether you need help selecting the best product for your application or more information on a particular device, our knowledgeable staff is here to provide you with the answers you need. Contact us today for more information about how we can help you get the products and support you need!

Product Brand

IT4Automation Ltd offers an exceptional online shopping experience through our user-friendly shop. With real-time stock information, access to product firmware, and a diverse range of products from various top-tier brands, customers are provided with a comprehensive and efficient shopping process. Our platform also allows for personalised account management, including viewing stock levels, creating custom quotes & invoices, and managing spending limits & multi-factor authentication setup. Further enhancing the customer experience, IT4A’s Resource Centre provides a wealth of information, while our 24/7 system monitoring services and post-sale support ensure customers receive the best possible service.

ICF-1180I Series

A series refers to a collection of related products or components designed to work together seamlessly, typically within a specific industry or application. These series often share similar features and functionalities, ensuring compatibility and ease of integration for users.
No data was found
Name Type Version Release Date

Datasheet for ICF-1180I Series

1.4 MB


Dec 13, 2022

Dec 13, 2022

QIG for ICF-1180I Series

2.0 MB


Jun 01, 2021

Jun 01, 2021

2D CAD for ICF-1180I

317.0 KB

2D CAD  
May 20, 2016

May 20, 2016

Show All

Supported Documents & Firmware Last Updated: February 6, 2023